Language
United Kingdom (EN)
Toggle Nav
My Basket
  • Sign In
Menu
Sign In
Language
United Kingdom (EN)
Account
main product photo
SKU
SOL-UK-PULSAR-ONLY-INSTALL

Kit Pulsar Plus (Installation incl.) Type 2 | 7.4kW

Includes installation through Wallbox installation partner. Following your purchase, you will be contacted within 24 hrs by the installer to start the process and book installation within 10 days.
Our installer is 5-start trust pilot rated.
By purchasing this item you agree to Wallbox sharing the contact details you provide with the third party installer for the sole purpose of contacting you to arrange installation.

View more details about the installation.
Complete your charging experience

Small is powerful.

Pulsar Plus was created to give your electric vehicle a powerful smart charger in an incredibly small size. It is perfect for daily use at home. It fits any garage and is enhanced by multiple functions found on the myWallbox app.

More Details

Short charging time and savings

  • Faster charging with up to 7.4kW
  • Smart scheduling for energy and cost savings
  • Easy indoor and outdoor installation
  • Voice control enabled with Amazon Alexa and Google Assistant devices
  • Integrated PEN fault protection. No earthing rod needed.
  • Compatible with all Wallbox Energy Management Solutions, including Eco-Smart solar EV charging, Power Boost dynamic load balancing and Power Sharing
More Information
Connector type Type 2
Maximum current 32 A
DC Leakage protection Included Yes
User interface myWallbox Portal, Wallbox App
Overvoltage Category CAT III
Storage temperature From -40ºC to 70ºC
RCCB Requires an external RCCB
Nominal frequency 50 Hz / 60 Hz
Degree of protection IP54 / IK08
Operating temperature From -25 ºC to 40 ºC
Input voltage 110 / 230 V AC ± 10% (1P) / 400 V AC ± 10% (3P)
Included features Power Sharing Smart
Dimensions 166x163x82mm
Charging power 7.4kW
Charging mode Mode 3
Charger status information Halo RGB LED, Wallbox App, myWallbox Portal
Cable length 5m
Other details Built In Earthing BS 7671:2018 - 722.411.4.1(iv)
Important note Installation Information:
  • Fitting of the Pulsar Plus on a brick or plaster wall, or to another suitable permanent structure.
  • The Pulsar Plus must be fixed to the main property and able to utilise the property’s earthing arrangement, (property’s earthing arrangement must meet current regulations - required by law).
  • Up to 10 metres of surface mount twin and earth cable, run and neatly clipped internally to the wall between the electricity distribution board/consumer unit and the Pulsar Plus point. Where armoured or protected cable is required (cable run outside) extra charges will apply.
  • RCD protected way on the consumer unit, for connection of the charge point circuit.
  • Routing of the cable through a drilled hole in a wall up to 500mm (20 inches) thick, if required.
  • The fitting and testing of electrical connections and protections required for the Pulsar Plus.
  • The Pulsar Plus must be installed on the main building.
  • RCD protected way on the consumer unit, for connection of the Pulsar Plus circuit.
  • Does not include groundworks.
  • The Pulsar Plus must be located in your designated off-street parking area and be fixed at a height where it can’t be hit by a vehicle.
  • Cable cannot be installed higher than 1.8 metres (6 feet) above the ground. If fixing higher than this is unavoidable then the installation may need to be paused – in that case, we will quote for any extra work needed.
  • When you are using your charger the EV charging lead must remain on your property and must not create a trip hazard for you or anyone else.
  • Our experts are not able to work in crawl spaces, on roofs or in lofts if it is deemed unsafe by them.
  • Our experts are not able to work in extreme weather (i.e. flooding or intense rain).
  • The design of your meter may vary, and will be determined based on current available stock. Rest assured, all meters have the same functionality when correctly installed and only differ in appearance.